Rear axle versions
The catalogue lists dozens of PD70 and PD80 rear axle builds (frames F2-1-2 – F2-1-32) with ratios of 13.7, 13.708, 15.78 and 18.16, different axle arms (F2-2), drive heads (F2-3) and differentials (F2-4). The axle ratio must match the gearbox, so parts are chosen by the axle number on its data plate, and when gears are replaced the number on the gear and the tooth count are checked as well (manual, Section F). Axle design and specifications are covered in our article on JCB 3CX / 4CX transmission.
PD70 rear axle assembly
JCB 3CX PD70 rear axle 450/44530, ratio 15.78:1 (JCB parts catalogue, frame F2-1-2). Click the image to view it full size.
| Item | JCB part no. | Description | Qty |
|---|---|---|---|
| A | 450/44530 | Axle assembly, 15.78:1, limited slip differential | 1 |
| 1 | 458/10978 | Axle arm with hub reduction (breakdown below) | 2 |
| 2 | 458/11086 / 458/11217 | Drive head 2.923:1 (before and after modification N44530/3, /4; formerly 458/10941) | 1 |
| 4 | 450/13302 | Breather plug | 1 |
| 6 | 458/20611 | Adaptor | 1 |
| 7 | 816/60040 | Grease nipple | 2 |
| 8 | 1321/3716 | Bolt M16×70 | 28 |
| 9 | 4102/1212 | JCB Multi-Gasket sealant | — |
Axle arm, hub reduction and brake plates
Rear axle arm with hub reduction 458/10978 (JCB parts catalogue, frame F2-2-1). Click the image to view it full size.
| Item | JCB part no. | Description | Qty |
|---|---|---|---|
| 1 | 458/20618 | Axle arm housing | 1 |
| 3 | 907/20043 | Taper roller bearing | 2 |
| 4 | 904/50033 | Cassette seal | 1 |
| 5 | 458/20446 | Wheel hub, 5-stud | 1 |
| 6 | 826/00923 | Wheel stud | 5 |
| 7 | 450/12702 | Annulus carrier | 1 |
| 8 | 450/12703 | Dowel bush | 8 |
| 9 | 826/01060 | Bolt M14×70 | 8 |
| 10 | 450/10205 | Annulus (ring gear) | 1 |
| 11 | 821/00210 | Internal circlip | 1 |
| 12 | 450/10206 | Planet gear | 3 |
| 13 | 450/10216 | Planet carrier, 5-stud | 1 |
| 14 | 907/50200 | Double row roller bearing | 3 |
| 15 | 821/00209 | Circlip | 6 |
| 16 | 2203/0054 | Circlip | 3 |
| 17 | 450/10208 | Driveshaft thrust washer | 1 |
| 18 | 914/M3544 | Driveshaft (superseded by two parts 914/M3544) | 1 |
| 19 | 450/12403 | Sun gear | 1 |
| 20 | 821/00494 | External circlip | 1 |
| 21 | 1321/0407Z | Bolt M10×25 | 2 |
| 22 | 828/00196 | O-ring | 1 |
| 23 | 826/00425 | Taper plug 3/4"-14PTF | 1 |
| 26 | 458/20353 | Brake friction plate | 5 |
| 27 | 458/20285 | Brake counter plate (steel) | 6 |
| 28 | 450/10213 | Reaction pin | 3 |
| 29 | 2203/0071 | External circlip | 2 |
| 33 | 450/10215 | Brake plate carrier | 1 |
| 57 | 458/20403 | Hub seal cover | 1 |
Each brake pack contains 5 friction plates and 6 steel counter plates. The manual requires worn or distorted plates to be replaced on both sides of the axle (Section G). The driveshaft (item 18) has been superseded in the catalogue: order two parts 914/M3544.
Drive head and brake pistons
JCB rear axle drive head 458/10941 (JCB parts catalogue, frame F2-3-2). Click the image to view it full size.
| Item | JCB part no. | Description | Qty |
|---|---|---|---|
| 1 | 450/17101 | Drive head housing | 1 |
| 2 | 907/09000 | Roller bearing | 1 |
| 3 | 921/01900 | Shim kit | 1 |
| 4 | 921/53400 | Spacer kit 12.625–13.950 mm | 1 |
| 5 | 907/08300 | Taper roller bearing | 1 |
| 6 | 904/50023 | Pinion seal, triple lip, 55 mm shaft | 1 |
| 7 | 454/13100 | Flange | 1 |
| 8 | 826/01483 | Nut M24 with washer | 1 |
| 10 | 826/01080 | Bolt | 12 |
| 11 | 458/70037 | Crown wheel and pinion 13/38 | 1 |
| 12 | 907/50100 | Taper roller bearing | 2 |
| 13 | 450/10403 | Differential adjusting nut | 2 |
| 14 | 826/00818 | Roll pin | 2 |
| 15 | 450/26310 | Limited slip differential assembly | 1 |
| 16 | 458/20365 | Brake piston housing | 2 |
| 17 | 1392/3407 | Screw M10×25 | 8 |
| 21 | 826/00919 | Dowel | 4 |
| 22 | 816/80012 | Magnetic drain plug 3/4" BSP | 1 |
| 23 | 1406/0021 | Sealing washer | 2 |
| 24 | 458/20371 | Brake piston, 139.4 mm diameter | 2 |
| 25 | 813/50012 | Brake piston seal | 2 |
| 26 | 813/50026 | Brake piston seal, square section | 2 |
| 27 | 816/80037 | Filler plug | 1 |
| 28 | 814/00365 | Spring | 6 |
| 29 | 450/18204 | Brake retraction pin | 6 |
| 30 | 448/16905 | Bush | 6 |
| 31 | 2203/1020 | Circlip | 6 |
The frame shows drive head 458/10941; on axle 450/44530 it has been replaced by 458/11086 and 458/11217, so part numbers for a particular axle should be checked against that axle’s own catalogue frame. The brake piston seals (items 25, 26) are leak tested using the procedure in the manual (page G-43), which is explained in our article on a JCB 3CX rear axle running hot.
Differential
JCB rear axle differential 450/10900 (JCB parts catalogue, frame F2-4-1). Click the image to view it full size.
| Item | JCB part no. | Description | Qty |
|---|---|---|---|
| 1 | 1315/3418 | Bolt | 8 |
| 2 | 450/10800 | Differential housing | 1 |
| 3 | 450/10903 | Cross shaft (planet pin), 163 mm | 2 |
| 4 | 450/16900 | Differential gear kit | 1 |
| 5 | 808/00209 | Side gear thrust washer | 2 |
| 6 | 808/00210 | Planet gear thrust washer | 4 |
Remote axle breather
JCB 3CX rear axle remote breather (JCB parts catalogue, frame F2-7-1). Click the image to view it full size.
| Item | JCB part no. | Description | Qty |
|---|---|---|---|
| 1 | 32/925678 | Breather with 330 mm hose | 1 |
| 2 | 648/03528 | Item 2 (formerly 648/21309) | 1 |
| 3 | 458/20611 | Adaptor | 1 |
| 4 | 821/00520 | Clip | 2 |
| 5 | 821/10220 | P-clip, d = 25 mm | 1 |
| 6 | 1315/3418Z | Bolt M10×80 | 1 |
| 7 | 123/06256 | Steel spacer, 5 mm | 1 |
A blocked breather lets pressure build up inside the axle, leading to oil seal leaks and brake problems (manual, page G-45).
Axle parts can be found in the rear axle category, brake plates and pistons in brake discs and brake pistons, bearings in bearings and seals in seals and oil seals. To choose a part, send us the axle number from its data plate and the machine serial number.





