This article covers the exploded views and parts lists for the JCB 3CX Syncro Shuttle manual gearbox with reverser from section F05 of JCB parts catalogue 9812/0010: the complete gearbox, the torque converter and mountings, the casings with filters and valves, the pump, the shafts with gears and synchronisers, the reverser and 4WD clutches and the gear lever. The catalogue covers 3CX-T machines with 92 and 100 hp engines, serial numbers 00960000–00989999, 01297000–01297999, 01327000–01349999, 01616000–01621599, 01705500–01709999. The main example below is gearbox 441/00670 (4WD, reduction gears 23/34). Part numbers shown as links open the product pages in our catalogue.

Gearbox versions

Section F05 lists four Syncro Shuttle builds: 441/00670 — 4WD, reduction gears 23/34 (frames F5-1); 441/00740 — 2WD (frames F5-2); 441/00680 — 4WD, gears 22/34 (frames F5-4); 441/00690 — 4WD, gears 22/35, built on the common parts group 441/00230 (frames F5-9). The 4WD versions carry the 4WD clutch 459/10119 with its cover and output flange, which the 2WD gearbox does not have; the reverser clutch 459/10097 is the same for all versions. Within one build, parts also change with modification numbers: for 441/00670 these are G/00670/1, G/00670/2 and G/00670/6, which determine the casings, solenoid valves and shaft setting parts. Parts are therefore chosen by the gearbox number together with the modification number. Gearbox design and checks are described in our article on JCB 3CX / 4CX transmission.

Gearbox assembly 441/00670

JCB 3CX Syncro Shuttle gearbox 441/00670, 4WD (JCB parts catalogue, frame F5-1-1)

JCB 3CX Syncro Shuttle gearbox 441/00670, 4WD (JCB parts catalogue, frame F5-1-1). Click the image to view it full size.

ItemJCB part no.PartQty
1441/00670Gearbox assembly, 4WD, reduction gears 23/341
2459/30382 / 459/30463Front casing (before and after modification G/00670/2)1
3459/30272 / 459/30435 / 459/M2870Rear casing SS700 4WD (before G/00670/1; after G/00670/2; after G/00670/6)1
4459/50701Drive gear, 23 teeth1
5459/50702Driven gear, 34 teeth1
9459/101194WD clutch assembly (exploded view below, frame F5-1-41)1
12813/50048Gasket1
13459/304514WD clutch cover1
14826/01417Flanged bolt M10 x 3010
16904/20172Triple-lip oil seal, shaft 55.0/54.811
17459/70133Propshaft yoke flange, 1480 series1
19826/01553Bolt1
20445/14001Dowel2

The gearbox housing is made up of a front and a rear casing; the catalogue designates the rear casing SS700 4WD. The reduction pair — a 23-tooth drive gear and a 34-tooth driven gear — transmits torque to the output shaft, while the 4WD clutch (item 9) under cover 459/30451 engages drive to the front axle. Triple-lip seal 904/20172 sits behind yoke flange 459/70133; the same seal is fitted behind flange 459/70317 (frame F5-1-21).

Torque converter and gearbox mountings

W300 torque converter, ratio 2.52, for 92 hp engines (JCB parts catalogue, frame F5-0-50)

W300 torque converter, ratio 2.52, for 92 hp engines (JCB parts catalogue, frame F5-0-50). Click the image to view it full size.

ItemJCB part no.PartQty
104/600784W300 torque converter, ratio 2.521
204/600136 / 04/600864Torque converter drive plate kit (version A — superseded, see TI 2/479; version B)1
304/500303Bolt4
404/501702 / 826/11605Bolt M8 x 20 (version A) / M8 x 30 (version B)6
5823/10297Hardened washer4

The torque converter transmits engine torque to the gearbox input shaft and is attached to the flywheel through a drive plate. The catalogue gives two drive plate versions: 04/600136 (A) is superseded by 04/600864 (B), and each version has its own bolt length — M8 x 20 and M8 x 30 respectively. The gearbox is fixed to the engine with twelve 1315/0409Z bolts (frame F5-0-5); the gearbox mounting bracket with its flexible mounts is shown in frame F5-0-1:

ItemJCB part no.PartQty
1335/06739Gearbox mounting bracket1
2331/40347 / 332/P7213Flexible mount (331/40347 — before modification M1348818)2
31315/3722ZBolt M16 x 1202
61315/3717ZBolt M16 x 752
10332/P7244Rebound washer 16x80x6 (previously 829/31165, 829/31272)2

Frame F5-0-30 shows the filler tube and dipstick: tube 332/06553 (up to modification M1617448) or 332/F4981 (from M1617449), dipstick 331/46204. The gearbox oil level check is explained in how to check the oil levels on a JCB 3CX.

Casings, filter, valves and pump

External parts of gearbox 441/00670: casings, filter, valve block (JCB parts catalogue, frame F5-1-11)

External parts of gearbox 441/00670: casings, filter, valve block (JCB parts catalogue, frame F5-1-11). Click the image to view it full size.

ItemJCB part no.PartQty
1459/30397 / 459/30464Flywheel housing (before and after modification G/00670/2)1
1432/902200Suction strainer1
1945/905000Pressure test point 1/4 BSP1
20813/50027Gasket1
23581/18076Gearbox filter element1
24813/10175Valve block gasket1
25459/10144Adaptor valve block SS700 Low Ratio1
3025/220998Solenoid valve assembly1
30A25/221054Coil, 12 V1
3135/100801Solenoid valve seal kit1
35701/80626Oil pressure sensor M12 (previously 701/80319, 701/80459, 701/80591; not supplied with the gearbox)1
40813/50041Rear seal1
4125/220992 / 25/220804 / 25/222913Solenoid valve (before G/00670/1; after G/00670/2) / cartridge valve with 2-screw fixing (after G/00670/6)1
41A25/221056Cartridge valve coil (before G/00670/1)1
43830/118424WD pipe, length 740 mm1
45814/10153Compression spring1
46459/70168Solenoid valve adaptor spool1

Oil is cleaned in two stages: by suction strainer 32/902200 and by replaceable filter element 581/18076. Valve block 459/10144 (SS700 Low Ratio) is mounted on the casing together with solenoid valve 25/220998 and its 12 V coil; the valves direct oil to the hydraulic clutches. The item 41 valve has changed twice: 25/220992 up to modification G/00670/1, 25/220804 with clamp plate 459/M2855 from G/00670/2, and cartridge valve 25/222913 from G/00670/6. The oil pressure sensor (item 35) is not supplied with the gearbox; in the frames for gearboxes 441/00740 and 441/00690, number 701/80626 is already shown as superseded by 701/M7305. Pressure test point 45/905000 is provided for pressure checks.

Gearbox pump and pump drive shaft (JCB parts catalogue, frame F5-70-1)

Gearbox pump and pump drive shaft (JCB parts catalogue, frame F5-70-1). Click the image to view it full size.

ItemJCB part no.PartQty
3459/50431Pump drive shaft, SS700 gearbox1
4904/20210O-ring1
5916/10012Ball bearing1
62203/1068Internal circlip1
1020/925552Gearbox pump assembly1
11904/20226Gearbox pump seal1
12813/50041Rear seal1
131315/3311ZBolt M8 x 454
14823/00291Copper washer M84

Pump 20/925552 supplies oil to the gearbox hydraulic circuit and is driven by shaft 459/50431 (listed in the catalogue as the SS700 gearbox pump drive shaft). The pump is sealed by seal 904/20226 and rear seal 813/50041 and secured with four M8 x 45 bolts with copper washers.

Shafts, gears and synchronisers

Internal parts of gearbox 441/00670: shafts, gears, synchronisers (JCB parts catalogue, frame F5-1-21)

Internal parts of gearbox 441/00670: shafts, gears, synchronisers (JCB parts catalogue, frame F5-1-21). Click the image to view it full size.

ItemJCB part no.PartQty
1826/01551Locknut M30 (46 mm A/F)1
3459/70317Yoke flange 1480, 35 splines1
4904/20172Triple-lip oil seal, shaft 55.0/54.811
5907/51600Taper roller bearing1
6921/53400Spacer kit, thickness 12.625 to 13.9501
7907/20045Taper roller bearing (previously 907/53800)1
8459/50208Transfer gear, 38 teeth, SS750 Low Ratio1
9907/20005Taper roller bearing1
11445/03300Synchroniser assembly1
12445/03010Synchroniser hub sleeve, 3rd/4th gear1
13459/502063rd gear, SS750 Low Ratio1
14459/50205Mainshaft gear SS7501
15907/52800Taper roller bearing 35 x 65 x 181
20459/70275 / 459/70378Mainshaft setting nut (before G/00670/1) / selective spacer kit (after G/00670/2)1
24459/70274 / 459/70379Layshaft setting nut (before G/00670/1) / selective spacer kit (after G/00670/2)1
26907/20049Taper roller bearing (previously 907/09600, 35 x 73 x 24)2
27459/50188Layshaft, Low Ratio1
28459/505112nd gear, 40 teeth, SS7001
29459/50520Synchroniser assembly1
31459/505091st gear, 44 teeth, SS7001
32917/02300Bearing2
33917/00008Bearing inner race1
35459/50440Idler gear, 35 teeth1
36917/51400Bearing2
37459/70206Idler gear spacer1
38459/70087Idler gear shaft1
39823/00451Thrust washer4
40917/02400Needle roller bearing1

The mainshaft carries 3rd gear 459/50206 and synchroniser 445/03300 with the 3rd/4th hub sleeve; the Low Ratio layshaft carries the 1st gear (44 teeth) and 2nd gear (40 teeth) with synchroniser 459/50520. Up to modification G/00670/1 the mainshaft and layshaft used setting nuts 459/70275 and 459/70274; from G/00670/2 these were replaced by selective spacer kits 459/70378 and 459/70379. Spacer kit 921/53400 (item 6) covers thicknesses from 12.625 to 13.950. For gearbox 441/00690 the catalogue lists 459/50534 (33 teeth) instead of 3rd gear 459/50206.

Reverser clutch and 4WD clutch

JCB 3CX reverser clutch 459/10097 (JCB parts catalogue, frame F5-1-31)

JCB 3CX reverser clutch 459/10097 (JCB parts catalogue, frame F5-1-31). Click the image to view it full size.

ItemJCB part no.PartQty
A459/10097Reverser (input) clutch assembly1
1459/50503Input clutch housing SS7001
2907/20012Taper roller bearing2
4459/50428Gear, 31 teeth, with plate carrier1
5459/50429Gear, 22 teeth, with plate carrier1
6459/10096Piston2
8823/10265Thrust washer 3.52 mm2
9917/10006Needle thrust bearing4
10917/50600Needle roller bearing2
11814/10115Splined disc spring2
15821/M2136Internal circlip (previously 826/10467)2
17828/10180Sealing ring2
18828/10181Sealing ring, 130 mm ID2
19904/50024Sealing ring4
20331/16520Friction plate10
21331/16516Steel counter plate10
23331/16517Pressure plate 6.0 mm2
24331/16519Shim 1.2 mm0 (as required)

The reverser clutch changes the direction of travel between forward and reverse without taking the gearbox out of gear. It consists of two clutch packs on a common housing 459/50503: one with a 31-tooth gear and one with a 22-tooth gear. For the whole unit the catalogue lists 10 friction plates 331/16520, 10 steel plates 331/16516, 2 pressure plates of 6.0 mm and 2 pistons 459/10096; the 1.2 mm shims are selected on assembly. The unit also includes 4 sealing rings 904/50024 and needle bearings 917/10006 and 917/50600.

4WD clutch 459/10119 (JCB parts catalogue, frame F5-1-41)

4WD clutch 459/10119 (JCB parts catalogue, frame F5-1-41). Click the image to view it full size.

ItemJCB part no.PartQty
2459/101194WD clutch assembly1
3904/14300Sealing ring (turquoise)1
4907/52800Taper roller bearing 35 x 65 x 182
5917/02700Needle roller bearing2
6445/19808Thrust washer 3.5 mm, phosphated1
8445/12307Steel counter plate10
9445/03205Friction plate10
10828/00414Sealing ring, 123.5 mm ID1
11459/504834WD clutch housing1
14449/10601Pressure plate 4 mm1
16814/00297Spring1
17828/00224Sealing ring 39.7 x 3.53 mm1
18445/12316Piston with oil deflector1
19445/12314Toothed shim0 (as required)

The 4WD clutch engages drive to the front axle. It contains 10 friction plates 445/03205, 10 steel plates 445/12307 and a 4 mm pressure plate; piston 445/12316 comes with an oil deflector, and toothed shim 445/12314 is selected on assembly.

Gear lever and selector mechanism

Gear lever 459/10143 and selector forks (JCB parts catalogue, frame F5-1-51)

Gear lever 459/10143 and selector forks (JCB parts catalogue, frame F5-1-51). Click the image to view it full size.

ItemJCB part no.PartQty
A459/10143Gear lever and housing assembly1
1459/30295Gear lever housing1
2445/10802Gear lever ball pivot1
3445/05501Gear lever1
4459/70271Lower selector lever1
10331/25566Gear lever gaiter1
14814/00221Gear lever spring1
17459/302971st gear selector fork1
18459/M2082Selector rod (previously 459/70181)1
19459/70199Selector rod pad2
20459/M2082Selector rod (previously 459/70181)1
21459/302993rd gear selector fork1
22445/03031Interlock roller1
24916/00006Detent ball 11 mm2
25814/00354Detent spring2
26816/80057Detent plug2
31813/50042Gasket1

Gear lever 445/05501 sits on a ball pivot in housing 459/30295 and is covered by gaiter 331/25566. Through the lower lever it moves the selector rods carrying the 1st and 3rd gear forks; rods 459/70181 have been superseded by 459/M2082. The rods are held in position by 11 mm detent balls with springs and plugs, and interlock roller 445/03031 prevents two gears being engaged at once. The lever housing is fitted to the gearbox with gasket 813/50042.

Gearbox parts are listed in the transmission and gearbox category, and gearbox filters in genuine JCB filters. The rear axle exploded view with part numbers is in our article JCB 3CX rear axle parts breakdown. When choosing a part, check the gearbox number and modification number against the catalogue parts list, or send us the machine model, serial number and JCB part number.

Parts enquiries

+90 531 224 49 66WhatsAppTelegraminfo@jcbpro.net
Monday–Saturday, 9:00–18:00, closed on Sunday

17/11/2026 8
More from this section
17/11/2026 9
JCB 3CX wheels, tyres and propshafts: drawings and part numbers from the JCB catalogue
This article covers sub-section F03 “Wheels, tyres & propshafts” of JCB parts catalogue 9812/0010 for the JCB 3CX backhoe loader, with exploded views and parts lists: the front and rear axle propshafts with their universal joints, wheel and tyre assemblies for rear-wheel-drive (2WD) and four-wheel-drive (4WD) machines, rear wheels, wheel rims, wheel nuts, valves and inner tubes. The catalogue applies to 3CX-T machines rated at 92 and 100 hp with serial numbers 00960000–00989999, 01297000–01297999, 01327000–01349999, 01616000–01621599, 01705500–01709999. Part numbers shown as links open the product pages in our catalogue.
07/10/2026 76
JCB 3CX PD70 rear axle parts breakdown: drawings and part numbers from the JCB catalogue
This article brings together the drawings and parts lists for the PD70 rear axle of the JCB 3CX backhoe loader from the JCB parts catalogue: the complete axle, the axle arm with hub reduction and brake plates, the drive head with brake pistons, the differential and the remote breather. The example is axle 450/44530 with a 15.78:1 ratio and limited slip differential, fitted to 3CX-T machines with front wheel steering (catalogue 9812/0010, serial numbers 00960000–00989999, 01297000–01297999, 01327000–01349999, 01616000–01621599, 01705500–01709999). Part numbers shown as links open the product pages in our catalogue.
07/10/2026 85
JCB 3CX and 4CX cooling system: radiator, fan, expansion tank, drawings and part numbers
On JCB 3CX and 4CX backhoe loaders with the JCB Dieselmax engine the cooling system consists of a cooler pack (engine radiator plus the hydraulic and transmission oil cooler), a fan with a viscous coupling (or a direct drive fan), an expansion tank and the hoses. System capacity is 18.5 litres. Below are the assembly drawings with JCB part numbers from the JCB parts catalogue for 3CX-T machines with Tier 2 engines (catalogue 9812/0010, serial numbers 00960000–00989999, 01297000–01297999, 01327000–01349999, 01616000–01621599, 01705500–01709999), together with maintenance data from the service manual.
07/10/2026 134
JCB 3CX and 4CX wiring diagrams before and after May 2009: sheets and component keys
Section C of the JCB service manual (publication 9803/3290-15) gives the JCB 3CX and 4CX backhoe loader wiring diagram in two versions: one for machines built up to May 2009 with analogue instruments and one for machines from May 2009 with the digital instrument panel. On the earlier machines the main machine circuit takes two sheets, with separate circuits for the gearboxes and options; the later circuit runs to 15 sheets. Below are the main sheets, the component keys and a guide to reading wire numbers.
07/10/2026 90
JCB 3CX and 4CX hydraulic circuit diagrams by build year, with component keys
There is no single hydraulic circuit for the JCB 3CX and 4CX backhoe loader: it depends on the build year and the pump type. Section E of the JCB service manual (publication 9803/3290-14) gives separate circuits for the gear pump 3CX built before and after September 2007, for the variable flow 4CX (7-spool and 6-spool), and for the 3C-14 (214e) and 3C machines. Below you will find the circuits themselves, the component keys and some notes on tracing the oil flow through a circuit.

This site uses essential cookies (session, cart, language, currency). If you click «Accept», Google Analytics and Yandex Metrica cookies are also used for visit statistics; if you click «Decline», they are not loaded. Personal data is processed under the Turkish data protection law KVKK No. 6698. Details: Privacy and cookie policy.