826/00919
  • Article
    826/00919
  • Machine system
    Front axle
  • Part type
    Dowel
  • Machine brand
    JCB
  • Manufacturing type
    Aftermarket
  • All the features
In stock
0.00 ₺
We do not publish prices: they depend on exchange rates and change often. Click «Request price» and we will quote the current price on the day you ask.
Check the exact specifications and compatibility with your machine with our managers.
We are available Monday to Saturday, 9:00 – 18:00; closed on Sunday.
Free delivery to the carrier of your choice, or collect your order in Istanbul.
Could not find the part you need? Write to us and we will help you find an alternative or order it from the manufacturer.

For the JCB machines: dowel 16 x 55 826/00919, an aftermarket part. This part is a solid dowel that aligns two parts to each other.

Dowels are small parts, but they are needed for axle joints to line up correctly: a joint assembled without a dowel or with a worn one lets the parts shift, so the bearings and seals run off-centre. The dowels removed during an axle repair are therefore always checked, and crushed or burred ones are renewed. The dowel is chosen by part number with the same diameter and length as the old one. Dowel wear usually shows that the joint has been working loose.

Specifications


Part number826/00919
Production typeAftermarket
Part typeDowel
System / groupFront axle
Machine makeJCB

Compatibility

According to sources, 826/00919 is a 16 x 55 mm dowel; the product card gives it as a key. Other parts are in Rear axle.

Fitting

Dowels are inspected whenever the joint is dismantled and renewed if crushed, burred or worn. Tap the new dowel gently and squarely into its bore and tighten the bolts to the specified torque. The dowel is chosen by part number, since its diameter and length decide the accuracy of the joint. The dowel comes new; clean its bore before fitting and check that no burrs remain. Look over the joint's bolts and washers too. Clean and deburr the holes before fitting the dowel or ring.

Specifications

  • Machine system
    Front axle
  • Part type
    Dowel
  • Machine brand
    JCB
  • Manufacturing type
    Aftermarket
Questions: 0
Your question:

No questions about this product.

JCB 3CX / 4CX 07/10/2026 77
JCB 3CX PD70 rear axle parts breakdown: drawings and part numbers from the JCB catalogue
This article brings together the drawings and parts lists for the PD70 rear axle of the JCB 3CX backhoe loader from the JCB parts catalogue: the complete axle, the axle arm with hub reduction and brake plates, the drive head with brake pistons, the differential and the remote breather. The example is axle 450/44530 with a 15.78:1 ratio and limited slip differential, fitted to 3CX-T machines with front wheel steering (catalogue 9812/0010, serial numbers 00960000–00989999, 01297000–01297999, 01327000–01349999, 01616000–01621599, 01705500–01709999). Part numbers shown as links open the product pages in our catalogue.
Useful articles 07/10/2026 52
JCB 3CX / 4CX Rear Axle Overheating: Causes and What to Check
The rear axle of a JCB 3CX or 4CX backhoe loader runs hotter than the front axle by design: it houses the oil-immersed service brakes, one multi-plate brake pack on each half shaft. A warm axle casing after a shift is therefore normal. It becomes a concern when the axle gets very hot after an ordinary road run, the machine feels as if it is dragging, there is a smell of burnt oil from the axle, or oil starts leaking past the seals. The usual cause is brake drag: the service brakes or the park brake are not releasing fully. Below, based on the JCB service manual, is what to check and in what order.
JCB 3CX / 4CX 07/10/2026 78
JCB 3CX / 4CX Transmission: Gearboxes, Axles, Pressures and Stall Test
Section F of the JCB service manual covers the transmission of the JCB 3C, 3CX and 4CX backhoe loaders: Synchro Shuttle SS700, Powershift PS764 and PS766 gearboxes, torque converter, front and rear axles, propshafts and oil cooler. It contains technical data, gearbox operation and electrics, pressure tests, the torque converter stall test, fault finding tables and removal procedures. This is issue 9803/3290-16 of the manual; the PDF runs to 306 pages.
Useful articles 02/10/2026 77
Which gearbox and axles are fitted to your JCB 3CX/4CX
Gearbox and axle parts are matched to a specific unit. Here is which transmissions and axles are fitted to JCB 3CX and 4CX backhoe loaders and how to tell them apart. The data comes from the JCB service manual for 3C, 3CX and 4CX backhoe loaders (machines with serial numbers 960001–989999, 1327000–1349999 and 1616000–1625999).
Similar products
448/26402
Axle bush, inner 448/26402 JCB Loadall, aftermarket
450/10215
Brake plate carrier gear 450/10215 JCB 3CX/4CX, OEM
448/26404
Axle bush, outer 448/26404 JCB Loadall, aftermarket
448/26302
Axle bush, inner 448/26302 JCB Loadall, aftermarket
458/20814
Propshaft yoke flange 458/20814 JCB, aftermarket
Propshaft yoke flange 458/20814 JCB, aftermarket
In stock
0.00 ₺

This site uses essential cookies (session, cart, language, currency). If you click «Accept», Google Analytics and Yandex Metrica cookies are also used for visit statistics; if you click «Decline», they are not loaded. Personal data is processed under the Turkish data protection law KVKK No. 6698. Details: Privacy and cookie policy.