Section 3 of JCB service manual 9813/0200 deals with routine maintenance of the JCB Loadall 527-58 telescopic handler: the service schedule by hours, oils, fluids and capacities, greasing points, and the checks on the engine, fuel system, hydraulics, transmission, brakes, electrics, tyres and boom wear pads. The PDF runs to 94 pages.

Service manual 9813/0200 applies to the compact Loadall 527-58 telehandler with hydrostatic transmission. According to the machine variants table (page 1-2-1), two JCB Dieselmax engines were fitted: the turbocharged SD rated at 63 kW (85 hp) and the turbocharged, charge-cooled SF rated at 74 kW (100 hp). The transmission was offered in four maximum speed versions: 20, 25, 34 and 40 km/h.

Page-by-page contents: JCB Loadall 527-58 routine maintenance

PagesWhat the section covers
3-1-2 – 3-1-7Service requirements, health and safety
3-1-8 – 3-1-13Service schedules
3-1-14 – 3-1-19Fluids, lubricants and capacities
3-1-20 – 3-1-27Preparing the machine for maintenance, cleaning, checking for damage
3-1-28 – 3-1-34Greasing and oiling
3-1-35 – 3-1-44Access panels, heater and air conditioning
3-1-45 – 3-1-56Brakes, electrics, fuses
3-1-57 – 3-1-76Engine, fuel system, hydraulics
3-1-77 – 3-1-90Transmission, tyres, wheel alignment (phasing), boom wear pads, screen washer, fire extinguisher

Service intervals

Maintenance is due by hour meter reading or by calendar, whichever comes first (page 3-1-8): 10 hours means daily, 50 hours weekly, 500 hours every six months, 1000 hours yearly, 2000 hours every two years and 6000 hours every six years. The first service, after 100 hours or one month of work, is carried out by the dealer.

  • Every 10 hours: check the coolant, engine oil, transmission motor gear train oil and brake fluid levels; wheel nut torque and tyres; check steering and wheel phasing, the transmission, all hydraulic services, brakes, electrics, the load moment indicator (LMI), seat belts and forks.
  • Every 50 hours: drain the water separator; check the axle and hydraulic tank oil levels; grease the axle pivots and linkages, the lift, compensation, tilt and steer ram pivot pins and the carriage lock pins.
  • Every 500 hours: change the engine oil and filter, the water separator filter, the axle oil and the hydraulic filter; check the front end accessory drive (FEAD) belt, mountings and hoses; clean the radiator; service the cab filter; apply Waxoyl to the boom wear pad runways, lubricate the inner boom hoses and check the wear pad clearance.
  • Every 1000 hours: air filter outer element, fuel filter, crankcase ventilation filter, hub oil and the extension ram pivot pin.
  • Every 2000 hours: renew the coolant, the air filter inner element, the hydraulic oil (taking an oil sample), the brake fluid and the control valve pilot filter; check and adjust the valve clearances.
  • Every 6000 hours: renew the FEAD belt, the injectors, the injector leak-off rail and the high-pressure fuel lines.

Footnotes to the schedule: under arduous operating conditions the engine oil and filter and the boom wear pads are serviced every 250 hours, and on B20 biodiesel the engine oil is also changed every 250 hours.

Oils, fluids and capacities

ItemCapacityFluid (JCB part number)
Fuel tank70 ldiesel fuel
Engine12.5–15 l (min. – max.)JCB Engine Oil EP 15W40 (4001/1805), −10 to +50 °C; EP 5W40 (4001/2705) for cold climates
Cooling system22 lJCB Antifreeze HP/Coolant mixed with water (4006/1120); fill at no more than 6 l/min
Transmission motor gear train3.5 lJCB HP Gear Oil 90 (4000/0305)
Front axle: housing / hubs13 l / 2 l eachJCB Special Gear Fluid Plus (4000/2205)
Rear axle: housing / hubs10.4 l / 2 l eachJCB Special Gear Fluid Plus (4000/2205)
Brakes (non-boosted system)—JCB Hydraulic Fluid HP15 (4002/0503); do not use ordinary brake fluid
Hydraulic tank51 lJCB Optimum Performance HF 68 (4002/2705), or HF 46 (4002/2005) for cold conditions
Grease points—JCB Special HP Grease (4003/2017)

Figures from pages 3-1-14 and 3-1-15. Antifreeze: a 50 % mixture protects down to −40 °C and 60 % down to −56 °C; never exceed 60 % (page 3-1-16). If general-purpose MPL-EP grease is used instead of the factory-specified grease, the greasing intervals are shortened: 50 hours becomes 10 hours and 500 hours becomes 50 hours.

Check values and torque settings

  • Sump drain plug and oil filter housing plug: 40–60 Nm; once the oil filter seal makes contact, tighten the filter by at least another 3/4 turn (page 3-1-58).
  • Fuel filter clamp: 24 Nm; hydraulic filter cover: 20 Nm (pages 3-1-69, 3-1-74).
  • Wheel nuts: 680 Nm, tightened in a diagonal sequence. On a new machine and after a wheel has been removed, check them every 2 hours (page 3-1-83).
  • Maximum boom wear pad clearance is 1.5 mm; check it every 500 hours (page 3-1-88).
  • Park brake test: the machine must not move at 1700 rev/min, and the test must not last longer than 20 seconds (page 3-1-45).
  • The FEAD belt is tensioned automatically; a 16 mm socket is needed to remove it (page 3-1-61).
  • Do not work on the hydraulics until the oil has cooled below 40 °C. Before stopping the engine, let it idle for 4 minutes (pages 3-1-36, 3-1-71).

Filters for servicing are listed under genuine JCB filters and aftermarket filters for JCB, oils and antifreeze under oils and lubricants, and drive belts under JCB belts.

Other sections of the JCB Loadall 527-58 service manual: general data and torque settings, hydraulics, transmission and axles, brakes and steering, engine, electrics and electronics, boom, chassis and cab. To choose a part, send us the machine model, the serial number and the JCB part number if you know it.

Parts enquiries

+90 531 224 49 66WhatsAppTelegraminfo@jcbpro.net
Monday–Saturday, 9:00–18:00, closed on Sunday

17/11/2026 19
More from this section
17/11/2026 28
JCB Loadall 527-58 Boom, Body and Cab: Service Manual Section B
Section B of JCB service manual 9813/0200 covers the boom, body and cab of the JCB Loadall 527-58 telescopic handler: the fork carriage, heating and air conditioning, the longitudinal load moment indicator and control system (LLMI/LLMC), the cab, fuel tank and chassis panels, the boom with its wear pads and shims, and the axle load sensor. The PDF runs to 148 pages.
17/11/2026 32
JCB Loadall 527-58 Electrics and Electronics: Service Manual Sections C and M
Sections C and M of JCB service manual 9813/0200 cover the electrical system and electronic network of the JCB Loadall 527-58 telescopic handler. The machine uses a 12 V negative earth system. The transmission, hydraulics, joystick, load moment indicator and Loadall Monitoring System (LMS) ECUs exchange data over a CAN bus, and fault codes are shown on the display or read with Servicemaster. The sections include a 25-sheet wiring diagram, harnesses, charging, alternator, battery, CAN bus, LMS, fault codes and how to work with Servicemaster. The two PDFs run to 118 and 134 pages.
17/11/2026 27
JCB Loadall 527-58 Engine: Dieselmax SD and SF, Service Manual Section K
Section K of JCB service manual 9813/0200 covers the engine of the JCB Loadall 527-58 telescopic handler. The machine is powered by a four-cylinder JCB Dieselmax with a mechanical rotary fuel injection pump, built in two versions: SD, turbocharged, and SF, turbocharged and charge-air cooled. The section includes the technical data, starting and stopping, the cold start heater, engine removal and replacement, plus the starter motor, cooling pack, coolant expansion tank, exhaust silencer, air filter vacuum switch, throttle pedal and hand throttle. The PDF runs to 66 pages.
17/11/2026 28
JCB Loadall 527-58 Brakes and Steering: Service Manual Sections G and H
Sections G and H of JCB service manual 9813/0200 cover the brakes and steering of the JCB Loadall 527-58 telescopic handler. The service brakes are oil-immersed multi-plate units in the centre of the front axle, while the park brake is a cable-operated disc brake. Steering is fully hydraulic, with 2WS, 4WS and crab modes selected either manually or automatically. The two PDFs run to 66 and 102 pages.
17/11/2026 25
JCB Loadall 527-58 Transmission and Axles: Section F of Service Manual 9813/0200
Section F of JCB service manual 9813/0200 covers the transmission of the JCB Loadall 527-58 telescopic handler and runs to 148 pages in the PDF. The machine has a hydrostatic transmission with infinitely variable speed: an axial piston hydrostatic pump on the engine supplies the drive motor, and the motor drives both axles through a transfer gearbox and propshafts. The section gives technical data for the pumps and motor in every speed version, describes the hydraulic and electrical operation of the transmission and covers pressure testing, fault finding, the axles, propshafts and speed sensors.

This site uses essential cookies (session, cart, language, currency). If you click «Accept», Google Analytics and Yandex Metrica cookies are also used for visit statistics; if you click «Decline», they are not loaded. Personal data is processed under the Turkish data protection law KVKK No. 6698. Details: Privacy and cookie policy.