450/10213
  • Brand
    CORA
  • Article
    450/10213
  • Machine system
    Transmission
  • Part type
    Brake plate guide pin
  • Machine brand
    JCB
  • Manufacturing type
    Aftermarket
  • Machine series
    3CX, 4CX, 5CX
  • Outer diameter, mm
    15
  • Length, mm
    83
  • All the features
In stock
0.00 ₺
We do not publish prices: they depend on exchange rates and change often. Click «Request price» and we will quote the current price on the day you ask.
Check the exact specifications and compatibility with your machine with our managers.
We are available Monday to Saturday, 9:00 – 18:00; closed on Sunday.
Free delivery to the carrier of your choice, or collect your order in Istanbul.
Could not find the part you need? Write to us and we will help you find an alternative or order it from the manufacturer.

Brake plate guide pin 450/10213 is an aftermarket part for the JCB 3CX and 4CX backhoe loaders. This pin is the brake reaction (guide) pin that guides the brake plates and stops them rotating.

Pins inside the axle and in the steering joints hold gears, brake plates or joints in the right position and carry load. The differential pin is the axis on which the planet gears turn; brake reaction pins stop the brake plates rotating and pass the braking torque to the axle casing; steering pivot pins are the pivot point of the knuckle joints. A worn pin causes play, knocking and rapid wear of the related gears or bores. Most pins are made of hardened steel with a ground surface, so their dimensions must match those of the old pin exactly.

Specifications


Part number450/10213
Production typeAftermarket
Part typeBrake plate guide pin
System / groupTransmission
Machine makeJCB
Series / model3CX, 4CX, 5CX
Outer diameter15 mm
Length83 mm

Compatibility

According to sources, 450/10213 is the brake reaction pin of JCB 3C, 3CX, 3D and 214-217 backhoe loaders, about 83 mm long and 15 mm in diameter. Other parts are in Rear axle.

Fitting

The pin comes new. Before fitting, lubricate it with clean axle oil or grease and slide it squarely into its bore without hammering. Renew the retaining parts (circlips, tension pins, split pins). After assembly, fill the axle with the specified oil and grease the steering pin nipples. Before fitting the pin, measure the bore diameter, and repair an oval or scored bore along with the pin change. For differential pins, also check the thrust washers and inner surfaces of the planet gears, since worn washers increase the gear clearances and make the differential noisy on turns.

Specifications

  • Machine system
    Transmission
  • Part type
    Brake plate guide pin
  • Machine brand
    JCB
  • Manufacturing type
    Aftermarket
  • Machine series
    3CX, 4CX, 5CX
  • Outer diameter, mm
    15
  • Length, mm
    83
Questions: 0
Your question:

No questions about this product.

JCB 3CX / 4CX 07/10/2026 77
JCB 3CX PD70 rear axle parts breakdown: drawings and part numbers from the JCB catalogue
This article brings together the drawings and parts lists for the PD70 rear axle of the JCB 3CX backhoe loader from the JCB parts catalogue: the complete axle, the axle arm with hub reduction and brake plates, the drive head with brake pistons, the differential and the remote breather. The example is axle 450/44530 with a 15.78:1 ratio and limited slip differential, fitted to 3CX-T machines with front wheel steering (catalogue 9812/0010, serial numbers 00960000–00989999, 01297000–01297999, 01327000–01349999, 01616000–01621599, 01705500–01709999). Part numbers shown as links open the product pages in our catalogue.
Useful articles 07/10/2026 52
JCB 3CX / 4CX Rear Axle Overheating: Causes and What to Check
The rear axle of a JCB 3CX or 4CX backhoe loader runs hotter than the front axle by design: it houses the oil-immersed service brakes, one multi-plate brake pack on each half shaft. A warm axle casing after a shift is therefore normal. It becomes a concern when the axle gets very hot after an ordinary road run, the machine feels as if it is dragging, there is a smell of burnt oil from the axle, or oil starts leaking past the seals. The usual cause is brake drag: the service brakes or the park brake are not releasing fully. Below, based on the JCB service manual, is what to check and in what order.
JCB 3CX / 4CX 07/10/2026 78
JCB 3CX / 4CX Transmission: Gearboxes, Axles, Pressures and Stall Test
Section F of the JCB service manual covers the transmission of the JCB 3C, 3CX and 4CX backhoe loaders: Synchro Shuttle SS700, Powershift PS764 and PS766 gearboxes, torque converter, front and rear axles, propshafts and oil cooler. It contains technical data, gearbox operation and electrics, pressure tests, the torque converter stall test, fault finding tables and removal procedures. This is issue 9803/3290-16 of the manual; the PDF runs to 306 pages.
Useful articles 02/10/2026 77
Which gearbox and axles are fitted to your JCB 3CX/4CX
Gearbox and axle parts are matched to a specific unit. Here is which transmissions and axles are fitted to JCB 3CX and 4CX backhoe loaders and how to tell them apart. The data comes from the JCB service manual for 3C, 3CX and 4CX backhoe loaders (machines with serial numbers 960001–989999, 1327000–1349999 and 1616000–1625999).
Similar products
450/18204
Brake back-off pin 450/18204 JCB 3CX/4CX, genuine
453/00303
Axle breather 453/00303 JCB 3CX/4CX, aftermarket
Axle breather 453/00303 JCB 3CX/4CX, aftermarket
In stock
0.00 ₺
32/925764
Axle breather 32/925764 JCB Loadall, aftermarket
Axle breather 32/925764 JCB Loadall, aftermarket
In stock
0.00 ₺
816/80037
Oil filler plug 816/80037 JCB, aftermarket
Oil filler plug 816/80037 JCB, aftermarket
In stock
0.00 ₺
816/80012
Axle drain plug (magnetic) 816/80012 JCB 3CX/4CX, genuine

This site uses essential cookies (session, cart, language, currency). If you click «Accept», Google Analytics and Yandex Metrica cookies are also used for visit statistics; if you click «Decline», they are not loaded. Personal data is processed under the Turkish data protection law KVKK No. 6698. Details: Privacy and cookie policy.