Caterpillar backhoe loader pins

Categories

07/10/2026 27

JCB JS200–JS260 Monitor Messages: What They Mean and What to Check

On JCB JS200, JS210, JS220, JS240 and JS260 tracked excavators with the AMS control system, the monitor in the cab shows the working mode, the time, gauges for oil temperature, coolant temperature and fuel level, and warnings in the message line. Each message first of all points to a real problem: low fuel or coolant, a blocked filter, overheating. But if a message stays on after the cause has been put right, the sensor, wiring or controller is at fault. Below is what each message means and what to check, based on Section C of JCB service manual 9803/6400.

07/10/2026 34

JCB JS200–JS260 Track Tension: How to Check the Sag and Adjust the Tracks

Track tension on the JCB JS200, JS210, JS220, JS240 and JS260 tracked excavators should be checked every shift. With the track raised off the ground, the gap between the underside of the track frame and the top of the track shoe at the fourth bottom roller from the front should be 275–295 mm on hard ground and 320–340 mm on soft sand and sticky clay. Tension is adjusted with grease through the valve on the track adjuster cylinder. The procedure below follows Section 3 of JCB service manual 9803/6400.

07/10/2026 22

JCB 3CX and 4CX Dipper Ram Creep: Causes, Ram Creep Tests and Repair

If the dipper of a JCB 3CX or 4CX backhoe loader drops on its own under load, there are three possible causes: a leaking piston seal in the ram, spool leakage in the excavator valve section, or a leaking auxiliary relief valve (ARV) in that section. The JCB service manual gives a test procedure that identifies the culprit before the ram is removed and stripped. Below are the test sequence, the permitted creep and the repair rules from Section E of service manual 9803/3290.

07/10/2026 27

JCB 3CX and 4CX Hydraulic Oil: HP32 or HP46, System Capacity and Changing the Oil

For the hydraulic system of JCB 3CX and 4CX backhoe loaders, the JCB service manual recommends ISO VG32 oil — JCB Hydraulic Fluid HP32 — at air temperatures below +38 °C. The more viscous ISO VG46, JCB High Performance Hydraulic Oil, is for air temperatures above +38 °C only. Machines with Advanced EasyControl joysticks need a separate all-season HV class oil, JCB Multigrade Anti Shear. The hydraulic system holds approximately 130 litres. The oil is changed every 2000 hours and the filter at every 500-hour service.

07/10/2026 33

JCB 3CX and 4CX Antifreeze: Which Coolant to Use, How Much and How to Change It

On JCB 3CX and 4CX backhoe loaders with the JCB Dieselmax engine, the coolant is renewed every two years, at the 2000-hour service. The cooling system holds 18.5 litres. The JCB service manual calls for an ethylene glycol antifreeze to ASTM D6210 with corrosion inhibitors and rules out organic acid technology (OAT) products. The standard mix is 50%, which gives protection down to −40 °C. Below we cover choosing, checking and changing the antifreeze as described in Section 3 of JCB service manual 9803/3290.

Default Name Model

372-5085

Lift ram rod pin 372-5085 CAT, aftermarket

In stock

0,00 ₺

380-2570

Lift ram rod pin 380-2570 CAT, aftermarket

In stock

0,00 ₺

6730887

Lift ram to frame pin 6730887 Bobcat, aftermarket

In stock

0,00 ₺

111-4342

Loader arm linkage pin 111-4342 CAT, aftermarket

In stock

0,00 ₺

216-8484

Loader arm linkage pin 216-8484 CAT, aftermarket

In stock

0,00 ₺

322-4587

Loader arm linkage pin 322-4587 CAT, aftermarket

In stock

0,00 ₺

360-2813

Loader arm linkage pin 360-2813 CAT, aftermarket

In stock

0,00 ₺

380-2566

Loader arm linkage pin 380-2566 CAT, aftermarket

In stock

0,00 ₺

216-8496

Loader bucket to arm pin 216-8496 CAT, aftermarket

In stock

0,00 ₺

438-0593

Loader bucket to arm pin 438-0593 CAT, aftermarket

In stock

0,00 ₺

6728819

Rear arm to boom pin, short 6728819 Bobcat, aftermarket

In stock

0,00 ₺

6732687

Rear arm to boom pin, threaded 6732687 Bobcat, aftermarket

In stock

0,00 ₺

310-0851

Swing ram rod pin 310-0851 CAT, aftermarket

In stock

0,00 ₺

300-5440

Swing tower taper pin 300-5440 CAT, aftermarket

In stock

0,00 ₺

328-8776

Swing tower upper pin 328-8776 CAT, aftermarket

In stock

0,00 ₺

Showing 25 to 39 of 39 (2 Pages)

Caterpillar pins (page 2)